Home > Fatal Error > Fatal Error Fet

Fatal Error Fet

Here's my memory of it: "I had verified that C-SPY correctly identifies my parallel port as LPT1. (This is on my laptop, which only has the one parallel port and my Thanks Gustavo. No license, either express or implied, by estoppel or otherwise, is granted by TI. Ryan Brown1 Nov 4, 2016 Updating those hard-to-reach industrial machines Have you ever found yourself... Source

Tools Insider University Program Groups Corporate Citizenship TI University Program Russian E2E (сообщество E2E) Japanese E2E (日本語コミュニティ) Learn E2E Launch Your Design Motor Drive & Control Videos More Cancel MSP Low-Power Follow Us TI Worldwide | Contact Us | my.TI Login | Site Map | Corporate Citizenship | m.ti.com (Mobile Version) TI is a global semiconductor design and manufacturing company. Content on this site may contain or be subject to specific guidelines or limitations on use. ANewUser I have the pin test connected and only VCC tool connected. https://e2e.ti.com/support/microcontrollers/msp430/f/166/t/100820

No license, either express or implied, by estoppel or otherwise, is granted by TI. Will a surname change after marriage invalidate the UK resident permit? Normally, you should have ogtten a request to update the FET firmware.

Thanks again Zhiwen Reply Cancel Cancel Reply Suggest as Answer Use rich formatting Prodigy 130 points Richa Trivedi Feb 14, 2012 4:33 AM In reply to zhiwen yao: Hi, I am Lorin Netsch Nov 8, 2016 MCUs can recognize what you say In our connected world we... I noticed that it is set to LPT1. Gustavo ---------------------------------------------------------------------------------------------------------Please click the Verify Answer button on this post if it answers your question.--------------------------------------------------------------------------------------------------------- Reply Cancel Cancel Reply Suggest as Answer Use rich formatting Prodigy 50 points Scott Chainey Mar

Session aborted. It wasn't > > obvious why the software wasn't made easier to operate, but > > there it is. > > > > > > I hope this helps. Windows has no problem with this, >finding it and annotating it as LPT1, with all appropriate >associations. https://e2e.ti.com/support/microcontrollers/msp430/f/166/t/516431 but I don't think so.

Reply Cancel Cancel Reply Suggest as Answer Use rich formatting Prodigy 10 points Monica DeZulueta Jul 21, 2011 8:11 PM In reply to anirban de: I get the same error with I > > see there that they actually listed what they imagine should be > > the I/O addresses for LPT1, LPT2, and LPT3. Factorial digit sum How do you solve the copied consciousness conundrum without killing anyone? If you still see the error after setting the port, it could be another fault with the FET debugger.

Ensure no other sftware has taken control. > -- No I dont have any other sftware hacking the LPT > > 4. Thank you in advance, Regards BM Prodigy 70 points burningmosfet Jul 28, 2011 2:41 PM Reply Cancel Cancel Reply Suggest as Answer Use rich formatting 5 Replies Prodigy Contents: 1.Embedded Electronic Systems and Microcontrollers; 2. See my bio for details.Before posting bug reports or ask for help, do at least quick scan over this article.

Ensure that MSP430 device is seated correctly. -- Yes. this contact form Content on this site may contain or be subject to specific guidelines or limitations on use. Thank you Zhiwen Reply Cancel Cancel Reply Suggest as Answer Use rich formatting Prodigy 20 points zhiwen yao Jul 31, 2011 1:44 AM In reply to Scott Chainey: Hi Scott, So, I think both XP and IAR are on same lines and it might not be and issue with parallel port ?? ------------- * I went through all other possible reasons

Same error here (Windows XP, MSP430F2274) Fri Feb 11 13:32:42 2011: Fatal error: Failed to re-initialize Session aborted! Which one is pin 1? Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff. © Copyright 1995-2016 Texas Instruments Incorporated. have a peek here i have already check the power supply(providing external power supply.) I am using TI's MSP-FET430UIF to program the device when connecing the device its not detecing as port in device manager(hardware

It does seem to help to power the target from an external source, but even then my success has only been marginally better. Failure. > > > "So I went back to the documentation and noticed a suggestion > > that sent me over to Tips and Tricks, Item (6) if I recall. Start using the MSP430 armed with a complete understanding of the microcontroller and what you need to get the microcontroller up and running!

When trying to run the IAR kickstart I get the following error "Fatal error: Could not find device (or device not supported) Session aborted!" I have tried many of the solutions

Tools Insider University Program Groups Corporate Citizenship TI University Program Russian E2E (сообщество E2E) Japanese E2E (日本語コミュニティ) Learn E2E Launch Your Design Motor Drive & Control Videos More Cancel MSP Low-Power Geoserver WFS getFeature with BBOX returns too much elements? As for the issue, is your MSP430 powered up? I'm pretty sure it was working fine last summer with version 5.1 Windows 7 MSP430G2231 Reply Cancel Cancel Reply Suggest as Answer Use rich formatting Prodigy 40 points bill pankau Mar

No license, either express or implied, by estoppel or otherwise, is granted by TI. It wasn't > obvious why the software wasn't made easier to operate, but > there it is. > > > I hope this helps. I seem to recall reading some useful help on this buried in the docs on the tool around page 5 or 6 of the user's guide. Check This Out The code composer studioreinstalled the drivers for the FET430UIF, and the IAR EW could not see the FET. ** THE FIX ** Uninstall the FET driver with device manager, reinstall

Ensure no other sftware has taken control. -- No I dont have any other sftware hacking the LPT 4. Thanks, Ryan Reply Cancel Cancel Reply Suggest as Answer Use rich formatting TI E2E™ Community Support Forums Blogs Videos Groups Site Support & Feedback Settings TI E2E™ Community Groups TI University The lower right corner is pin 2. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff. © Copyright 1995-2016 Texas Instruments Incorporated.

I am running the same Parallels VM environment and everything. It turns out that I should have read it a little closer. Hot Network Questions How to start building a regression model when the most strongly associated predictor is binary What do you call someone who acts "cool-headed"? Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff. © Copyright 1995-2016 Texas Instruments Incorporated.

Necessary to reboot computer to install drivers. -- YES I did.Morethan 1 times. 5.