Home > Fax Error > Fax Error 27992

Fax Error 27992

Contents

when trying to convert/open a 2gb pgn file: - when I use pgnscid in a terminal, it starts converting but fails at some point, saying "bus error" - when I try Re: scid problem with large pgn (Benoit St-Pierre) > 6. Call the telephone provider if line conditions fail to improve. The exact error code will vary depending on fax driver used. 27987 Can't Agree on Bit Rate The modem and the remote unit couldn't fall back to or agree upon any

Here's some debugging info: From gdb: (gdb) run /home/master/ChessBase/Database/Work/opening\ encyclopedia.pgn Starting program: /usr/games/bin/pgnscid /home/master/ChessBase/Database/Work/opening\ encyclopedia.pgn Converting file /home/master/ChessBase/Database/Work/opening encyclopedia.pgn to Scid database /home/master/ChessBase/Database/Work/opening encyclopedia: Errors/warnings will be written to /home/master/ChessBase/Database/Work/opening encyclopedia.err. Error Code(s) Definitions/Causes Solutions 200 The fax session completed without errors. How does HP install software and gather data? Failed Hangup: No loop current. (3) This means that once we dialed the number we got dead air, no ring tone and no answer. http://thewinwiki.org/fax-error-27992/

Fax Error Codes

It can also be caused if the receiving fax is using a fax format incompatible with the HP fax (usually during color faxing). Save and close Note: Product availability is calculated on a real-time basis and adjusted continuously. The click, heard for an incoming call, is actually a momentary disconnect of the line.

Specifically, fax tones or the fax handshake (connection) from the remote machine was not detected. This means that the number dialed rings but the call is never answered. I did look at Position::ReadMove() in position.cpp but did not find anything (yet). Sharp Fax Error Codes We suggest you test the number by calling it from a land line to see if you get a fax tone.

Try to send the fax using a different mode. Fax Error Codes Ricoh The primary cause for this is generally a poor connection to the destination fax machine. Search all support All Support Software, Drivers and Updates Troubleshooting How to Product Information User Guides Cancel Example: “Laserjet P1102w driver” or “HP Pavilion 17-f002na will not turn on” Loading Results great post to read Unspecified If our servers cannot determine the reason for a fax failure then the reason returned will be "Unspecified." Did you find it helpful?

For example, let's say that only 7200 and 9600 bps were enabled to prevent fall back to 4800 bps or slower on a noisy line(hence keeping phone bills smaller). Epson Fax Error Codes This occurs when the line is disconnected or if line conditions degrade during the session. I used the following trick: A Gzip compressed file (e.g. If this is the case, ask the sender to retry a normal transmission from the remote machine.

Fax Error Codes Ricoh

Retry the fax transmission when the line is no longer busy. 314 The local machine attempted to initiate a remote diagnostic session, but detected that remote diagnostics are disabled on the If these transmissions are successful, then notify the user of the remote machine to make them aware of the issue. Fax Error Codes Configure the machine to start reception at a lower speed. Fax No Answer When Sending This                               could be due to line impairment causing a timeout on the receive side, or a

Errors could still occur, and might result in degraded image quality on the received page. Please don't fill out this field. Toll Free Restricted Area The number being called is an 800 number that has a restriction placed by the owners that does not allow calls from our area code. This prevented the fax from receiving any more pages, and caused it to terminate the session prematurely. Ricoh Fax Error E3

Confirm that the remote user wants to initiate a poll transmission. We are working diligently to get this fixed. note: If errors occur every time a fax is sent or received, go to Troubleshooting Fax Transmission and Reception Issues. Retry the fax reception when telephone line conditions have improved.

Try the fax when telephone line conditions have improved. Canon Fax Error Codes Retry the fax reception when telephone line conditions have improved. Ask the user of the remote machine to turn it off for 10 seconds, and then turn it back on.

Loading...

Error                                     type: RETRYABLE.    27992 Receiver sent DCN: Normally, the receiver should never send This error might be associated with bad line conditions or might indicate a problem with the fax's modem. Enable ECM. Error Code 700 Error In Fax Transmission Remote Fax Aborted This means that a connection was established with the remote fax, but during the transmission of the fax the remote fax disconnected the call.

We suggest you test the number by calling it from a land line to see if you get a fax tone. On many fax machines, it is possible to accidentally initiate a fax reception in the following cases: There is no paper in the machine. The remote user pressed the Stop key while the reception was in progress. For non-ecm faxes, a DCN received after page data does not generate an error since some fax machines dont bother with a post page signal on the last page. 28003 V.34

Ask the community!