Solution: Boost the transmission level so signals can be properly received by the other party. The other machine may be trying to receive a fax instead of sending one, or it may already be in the process of receiving another fax. Cause: Abnormal protocol. Solution: Adjust the echo monitor time after CFR transmission so picture signals can be received properly. Source
Wait several minutes between the end of one transmission and the start of the next transmission. 383 ECM Disable ECM, and then try faxing again. Solution: Transmit to a FAX whose bits 33 and over are not defined. ##200 [ RX ] Fail to detect picture reception carrier for 5 seconds during reception. Solution: Check each part of the document transport unit for any abnormalities using the Service manual. ##121 [ RX ] Ink sheet and Recording paper cling together. Solution: Replace SCNT PWB Solution: Replace the modem or modem attached circuit board. ##271 [ RX ] Detected 1650 Hz binary signal after CFR transmission however, failed to receive check over here
A. A. Solution: Adjust the NL equalizer to receive the picture signals properly. ##012 [ RX ] Receive signals other than PIS and GC2 after detecting MCF2 or GI2 when EOM is Credentials confirmed by a Fortune 500 verification firm.
Solution: Replace the SCNT PWB. ##266 [ TX / RX ] Internal signal error. Cause: The other party cannot receive the signals properly due to low transmission level. The remote user should make sure paper is loaded in the machine, paper jams are fixed, and any error messages are cleared. 317 The remote machine cannot support a fax reception Hp Fax Error 388 Join the community of 500,000 technology professionals and ask your questions.
Cause: Defective internal unit; (the wait signal will not go off for 3 seconds when waiting to respond to the reader after pre-scanning the document length). Hp Fax Error 350 Gemini02 I work on behalf of HPClick the Thumbs Up below to say “Thanks” for helping! Cause: CFR echo malfunction. All the above actives may result in the deletion or corruption of the entries in the windows system files.
Solution: Refer to specific trouble shooting procedures in Service Manual. ##051 [TX / RX] Stepping Motor trouble. http://www.justanswer.com/computer/2zyyr-having-trouble-receiving-faxes-hp-officejet.html Question about PSC 2410 All-In-One InkJet Printer 1 Answer HP office jet 6210 All - in- one /error message 232 fax error codes for your printer. How To Disable Ecm On Hp Fax Machine i can not fax to this number and when i receive from it, it always prints a Fax Call Report. Fax Error 346 Solution: Replace the backup battery.
A. this contact form Let the machine sit for awhile so BJ head can cool down and retry. Cause: (DIS received) in CEP 2 transmission, the actual condition of the other party is different from that registered with the sending FAX. Calvin Yu Article Categories Business News Do-It-Yourself (DIY) Projects Productivity Printer Reviews Technology News Troubleshooting & Printer Tips Shop Ink and Toner Brother Ink Brother Toner Canon Ink Ecm Setting On Fax
B. A. Cause: Abnormal protocol; (fill or EOL present in picture data). have a peek here Have the telephone company check the line. 431 The sending fax machine did not receive a response after terminating a transmission.
Resend the document as two or more separate fax transmissions. Fax Error Codes Ricoh If these transmissions are successful, then notify the user of the remote machine to make them aware of the issue. A.
Disable ECM, and then try faxing again. 382 ECM The remote fax machine held the local fax machine from continuing the ongoing transmission because of a temporary low memory condition at B. Solution: Relax the RTN transmission conditions to prevent RTN transmission. Error Code 700 Error In Fax Transmission If the session fails after sending several pages of a large document, resend the document as several smaller documents.
A. A. Video Photos Link Add Upload Upload × × Draw a box over the problem!! http://theresab.com/fax-error/fax-error-code-388.html Solution: Press Start button after confirming the first DIS from the other party during a manual call.
Cause: The other party experienced echo malfunction. Solution: Add an EPT to the V29 modem signals Solution: Adjust the continuous transmission time of 1 before transmitting the picture signal so the other party can receive picture signals The following list describes when ECM will or will not be used: All faxes sent in color will use ECM All faxes sent at the highest transmission speed will use ECM A.