Home > Fax Error > Fax Error Codes Canon

Fax Error Codes Canon

Contents

Cause: Defective internal unit; (the wait signal will not go off for 3 seconds when waiting to respond to the reader after pre-scanning the document length). control source as part of auto-dialing. • The relay control source is wrongly regis- • Ask the operator of the relay machine to tered as part of auto-dialing of the relay Solution: Confirm the PWB's part numbers and use the proper combination. ##526 [ RX ] Fail phase synchronization in OLD-FM mode. A. http://theresab.com/fax-error/fax-canon-error-322.html

Page 111 Chapter 2: Service Error Codes ##293 [ RX ] After transmitting CFR, the carrier at the beginning of the image signal cannot be received for 6 sec Cause Remedy Basic Connection If the telephone line is connected correctly, there is a problem with your telephone line. As an alternative, suggest that the sender manually fax the document. The remote fax machine determined that there was a feature incompatibility between the two machines and terminated the session.

Canon Fax Error Code Ng

A. If the error persists, and error correction is in use for the fax session, disable ECM. Page 47 Chapter1: User Error Codes #099 [ TX/RX ] Stop button was pressed during a communication Cause Remedy • The Stop button was pressed during a com- • Try transmission

When a message is displayed on the LCD, check the cause. Send the document to a smaller number of recipients. #703 Cause 1 The memory for the image data is full. Solution: Refer to Service Manual. ##301 [ TX ] Interface error between reader and controller. Canon Fax Error Code 104 If the machine still does not operate normally, turn the main power OFF, and then back ON. (See "Before You Start Using This Machine.") #704 Cause 1 An error occurred while

The following paragraph does not apply to any countries where such provisions are inconsistent with local law. Canon Fax Machine Error Codes Cause: Cannot receive the picture signals from the other party properly due to poor line conditions. The repairs instructions are not limited to specific models and, therefore, tend to be general in nature. https://support.usa.canon.com/kb/index?page=content&id=ART141048 Page 215 Chapter 2: Service Error Codes ##1061 [ TX/RX ] Called party is closed or does not support the service [German model] Cause Remedy • Cause number #61 (Called party

Remedy Check the status of the network. #801 Cause You are sending a file to a destination to which you have no write permission. Canon Result Ng Page 101 Chapter 2: Service Error Codes ##265 [ TX/RX ] Signal error in the hardware of the system control board occurred Cause Remedy • An internal unit is faulty (i.e., Error Code(s) Definitions/Causes Solutions 420 421 A handshaking (connection) error occurred at some point in the process from the sending fax machine. Memory Transmission: In memory transmission, all documents data is read into memory before dialing for transmis- sion.

Canon Fax Machine Error Codes

Manual of the model in question. #039 [ TX ] Closed network transmission fails Cause... their explanation Cause Remedy 1-39... Canon Fax Error Code Ng to overflow. Canon Error #099 Solution: Replace the unit including the carriage cable.

Solution: Replace the modem or modem attached circuit board. http://theresab.com/fax-error/fax-error-codes-244.html To check a service error code, shift bit of service soft switch #1 SSSW SW01 to T. Page 218 Chapter 2: Service Error Codes ##1070 [ TX/RX ] Only restricted digital information bearer capability is available Cause Remedy • Cause number #70 (Only restricted digital • Start a Confirm that the remote user wants to initiate a poll transmission. Canon Fax Error #099

Solution: Replace the button control unit (operation unit, etc.). ##232 [ TX ] ENCODE control unit malfunction. A. Remedy Check to see that the power plug is firmly inserted into the power outlet and that it is not in a situation where the power can easily be turned OFF. http://theresab.com/fax-error/fax-error-codes-hp.html A.

Cause: Defective internal unit; (RECORD will not go on during memory copy). G3 Fax Solution: Boost the transmission level so the other party can receive the signals properly. Page 79 MCF, RTP, RTN, PIP, or PIN was received Cause Remedy • The procedure signal is faulty. • Record the protocol on a DAT or MD, and have it analyzed

Remedy Set the Different Size Originals mode, and then try scanning again.

Solution: Boost the transmission level so the other party can properly receive TCF. Page 41 Chapter1: User Error Codes #055 [ TX ] The other party does not have an MDC (Multi Device Controller) function [exclusively for GP55] Cause Remedy • Although an attempt Solution: Replace the crystal attached unit for 90% compression recording. Reserved Communication Jobs Were Cleared. Page 72 Chapter 2: Service Error Codes ##101 [ TX/RX ] The modem speed of the machine does not match that of the other party Cause Remedy • The modem speed

available) arrived from the network. • Print out a communications analysis list, and analyze it. When all documents have been read into memory, memory transmission reservation may be selected as in the case of memory transmission. On some models, you may make the closed network settings using the user soft switch and register a closed network ID as part of user data. 1 1 . Check This Out Lifecake Relive your best moments in one beautiful timeline.

Remedy Check the print settings, and try printing again. Cause: The machine was out of recording paper. Cause: Thermal head trouble Solution: Replace the Thermal head B. Cause: Cannot receive REJ due to poor line conditions.