Home > Fax Error > Fax Error Codes Ng

Fax Error Codes Ng

Contents

CFR echo inhibits training signal reception, resulting in time over. Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##738 [ RX ] Wrong block number during ARQ reception. Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual Faxphone_l75.pdf. Hot-Shot: An expert who has answered 20 questions. http://theresab.com/fax-error/fax-error-codes-hp.html

Solution: Have the other party boost the transmission level so this machine can receive the protocol signals properly. Brother Fax Machines ng means faxing result ng trying faxing result ng whats ng machine mean ng mean faxes report busy machine plugged wrong phone ng mean trying ng means report Solution: Replace the BJ printer control ROM. Solution: Replace the board containing a printer control ROM B.

Result Ng Canon

A. A. Press [OK].

Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##291 [ TX ] Receive non-DTC signal in DTC stand-by after the Solution: Replace the ink sensor and re-register the ink level ##332 [ TX / RX ] Printer control DRAM check error. Cause: Line noise. Canon Fax Ng #018 Solution: Add an EPT on the V29 modem signals.

Cause: Abnormal protocol. Fax Machine Poor Line Condition Out Of Memory Solution: Relax the TCF assessment standards to prevent FTT transmission. Cause: The operation of the UPI to control the G3 modem did not finish properly. their explanation DESTINATION ID The DESTINATION ID of the remote party is printed.

Cause: Cannot receive picture signal properly due to poor line conditions. Fax Result Cont A. Cause: The other party cannot receive the signals properly due to low transmission level. Ask the sender to resend the remaining pages. #080 Cause 1 A subaddress is not set in the recipient's machine.

Fax Machine Poor Line Condition Out Of Memory

B. Start dialing the # then press start. Result Ng Canon Solution: Boost the transmission level so the other party can receive properly. Fax Result Ng Poor Line Condition Solution: Power cycle the machine.

Cause: Motor trouble. http://theresab.com/fax-error/fax-error-codes-list.html When I send a fax, then the report prints out. A. Browse Categories Answer Questions Canon FaxPhone L75 Plain Paper Laser Canon Fax Machine Fax Machines All Unanswered Join Sign In Ask a Question × HomeForumFax MachinesCanonFaxPhone L75 Plain Paper LaserGetting Error Canon Fax Machine Error Codes

Solution: Replace the cleaning absorption waste ink pad. Solution: Replace the backup secondary battery. What does it mean? http://theresab.com/fax-error/fax-error-codes-244.html Solution: Add an EPT to the V29 modem signals Solution: Adjust the continuous transmission time of 1 before transmitting the picture signal so the other party can receive picture signals

Cause: Other party cannot properly receive signals due to poor line conditions. Konica Minolta Ng Fax Error Solution: Increase #2 MENU No. 07 transmission level within a range of -8 to -15 dBm, or set #1 SSSW SW28 bit 0 to 1 to inhibit the V.8/ V.34 protocol Solution: Have the other party boost the transmission level to receive picture signals properly. ##612 [ RX ] Fail to detect picture signals for 5 seconds after CFR transmission during

A.

Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##713 [ TX ] Receive signals other than RR, RNR or REJ Solution: Have the other party refill their machine with recording paper. ##008 [ RX ] Fail to receive GC2, PIS and Phase signals for 35 seconds and receive other signals during A. Konica Minolta Fax Error Code Ng Solution: Power cycle the machine (unplug unit).

Solution: Adjust the NL equalizer so the other party can receive picture signals properly. Source(s): received quot ng quot error send fax canon mx860 mean: https://biturl.im/jKsTP Jimmie · 1 year ago 0 Thumbs up 0 Thumbs down Comment Add a comment Submit · just now Solution: Boost the transmission level so the other party can receive picture or EOP signals properly. http://theresab.com/fax-error/fax-error-codes-canon.html Cause: Printer control DRAM malfunction Solution: Power cycle the machine.

Back To Top Solution: Boost the transmission level so that the other party can receive picture or Q signals properly. A. Cause: The other party cannot receive data properly due to poor line conditions.

Solution: Check each part of the document transport unit for any abnormalities using the Service manual. ##121 [ RX ] Ink sheet and Recording paper cling together.